Video streaming in QGroundControl

This page shows how to set up a a companion computer (Odroid C1) with a camera (Logitech C920) such that the video stream is transferred via the Odroid C1 to a network computer and displayed in the application QGroundControl that runs on this computer.

The whole hardware setup is shown in the figure below. It consists of the following parts:

  • Odroid C1
  • Logitech camera C920
  • WiFi module TP-LINK TL-WN722N


Install Linux environment in Odroid C1

To install the Linux environment (Ubuntu 14.04), follow the instruction given in the Odroid C1 tutorial. In this tutorial it is also shown how to access the Odroid C1 with a UART cable and how to establish Ethernet connection.

Set up alternative power connection

The Odroid C1 can be powered via the 5V DC jack. If the Odroid is mounted on a drone, it is recommended to solder two pins next to the 5V DC jack by applying the through-hole soldering method as shown in the figure below. The power is delivered by connecting the DC voltage source (5 V) via a jumper cable (red in the image above) with the Odroid C1 and connect the ground of the circuit with a jumper cable (black in the image above) with a ground pin of the Odroid C1 in the example setup.

Power Pins

Enable WiFi connection for Odroid C1

In this this tutorial the WiFi module TP-LINK TL-WN722N is used. To enable WiFi connection for the Odroid C1, follow the steps described in the Odroid C1 tutorial in the section Establishing wifi connection with antenna.

Configure as WiFi Access Point

This sections shows how to set up the Odroid C1 such that it is an access point. The content is taken from this tutorial with some small adaptions. To enable to stream the video from the camera via the Odroid C1 to the QGroundControl that runs on a computer it is not required to follow this section. However, it is shown here because setting up the Odroid C1 as an access point allows to use the system in a stand-alone fashion. The TP-LINK TL-WN722N is used as a WiFi module. In the ensuing steps it is assumed that the Odroid C1 assigns the name wlan0 to your WiFi module. Change all occurrences of wlan0 to the appropriate interface if different (e.g. wlan1).

Onboard Computer as Access Point

For a more in depth explanation, you can look at RPI-Wireless-Hotspot

Install the necessary software

sudo apt-get install hostapd udhcpd

Configure DHCP. Edit the file /etc/udhcpd.conf

start # This is the range of IPs that the hotspot will give to client devices.
interface wlan0 # The device uDHCP listens on.
remaining yes
opt dns # The DNS servers client devices will use (if routing through the Ethernet link).
opt subnet
opt router # The Onboard Computer's IP address on wlan0 which we will set up shortly.
opt lease 864000 # 10 day DHCP lease time in seconds

All other 'opt' entries should be disabled or configured properly if you know what you are doing.

Edit the file /etc/default/udhcpd and change the line:




You will need to give the Onboard Computer a static IP address. Edit the file /etc/network/interfaces and replace the line iface wlan0 inet dhcp (or iface wlan0 inet manual) to:

auto wlan0
iface wlan0 inet static
wireless-power off

Disable the original (WiFi Client) auto configuration. Change the lines (they probably will not be all next to each other or may not even be there at all):

allow-hotplug wlan0
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
iface default inet dhcp


#allow-hotplug wlan0
#wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
#iface default inet dhcp

If you have followed the Odroid C1 tutorial to set up the WiFi connection, you might have created the file /etc/network/intefaces.d/wlan0. Please comment out all lines in that file such that those configurations have no effect anymore.

Configure HostAPD: To create a WPA-secured network, edit the file /etc/hostapd/hostapd.conf (create it if it does not exist) and add the following lines:

channel=6            # Channel to use
ieee80211n=1          # 802.11n assuming your device supports it
# Change the to the proper driver
# Change these to something else if you want

Change ssid=, channel=, and wpa_passphrase= to values of your choice. SSID is the hotspot's name which is broadcast to other devices, channel is what frequency the hotspot will run on, wpa_passphrase is the password for the wireless network. For many more options see the file /usr/share/doc/hostapd/examples/hostapd.conf.gz. Look for a channel that is not in use in the area. You can use tools such as wavemon for that.

Edit the file /etc/default/hostapd and change the line:




Your Onboard Computer should now be hosting a wireless hotspot. To get the hotspot to start on boot, run these additional commands:

sudo update-rc.d hostapd enable
sudo update-rc.d udhcpd enable

This is enough to have the Onboard Computer present itself as an Access Point and allow your ground station to connect. If you truly want to make it work as a real Access Point (routing the WiFi traffic to the Onboard Computer’s Ethernet connection), we need to configure the routing and network address translation (NAT). Enable IP forwarding in the kernel:

sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward"

To enable NAT in the kernel, run the following commands:

sudo iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
sudo iptables -A FORWARD -i eth0 -o wlan0 -m state --state RELATED,ESTABLISHED -j ACCEPT
sudo iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT

To make this permanent, run the following command:

sudo sh -c "iptables-save > /etc/iptables.ipv4.nat"

Now edit the file /etc/network/interfaces and add the following line to the bottom of the file:

up iptables-restore < /etc/iptables.ipv4.nat

Gstreamer Installation

To install gstreamer packages on the computer and on the Odroid C1 and start the stream, follow the instruction given in the QGroundControl README.

If you cannot start the stream on the Odroid with the uvch264s plugin, you can also try to start it with the v4l2src plugin:

gst-launch-1.0 v4l2src device=/dev/video0 ! video/x-h264,width=1920,height=1080,framerate=24/1 ! h264parse ! rtph264pay ! udpsink port=5000

Where is the IP address where QGC is running.

If you get the system error: Permission denied, you might need to prepend sudo to the command above. Alternatively add the current user to the video group as shown below (and then logout/login):

  sudo usermod -aG video $USER

If everything works, you should see the video stream on the bottom left corner in the flight-mode window of QGroundControl as shown in the screenshot below.

If you click on the video stream, the satellite map is shown in the left bottom corner and the video is shown in the whole background.

results matching ""

    No results matching ""